West Bradford Township, PA

Installed in-line drain assembly on exhaust. Installed and wired EZ trap. Installed new inducer motor, under parts warranty. Walked through with homeowner. System operating well at this time.

Upon arrival for heat maintenance on heat pump tune up I changed the filter. Checked electrical and wiring and emergency heat kit. Checked blower motor and assembly. Checked delta t. Inspected coils. Checked fan motor and assembly. Checked refrigerant pressures via led lights on outdoor inverter board. Forced unit into defrost. Unit is in normal operation at this time.

Arrived to location to assess noise from boiler. Customer explained the noise they were experiencing coming from the boiler. It sounds like a motor high-pitched noise. Test operation of oil boiler. Cycle boiler couple times at aqua stat 180 degree water temp. Check pressure ok 18 psi. Could hear a noise coming from the actual boiler when the burner is firing. Noise is not present all the time. Noise is coming from chamber nothing to concern at this time. Inspect chimney base and top of boiler. Check relief valve would recommend replacement of relief valve there was lot of corrosion and buildup. Replaced relief valve and test operation ok. We will double check system when we come back to do boiler tuneup.

Performed 6 month tune up on trance gas furnace, checked unit in heating mode and tested combustion and gas pressures. Inspected drains and wire terminations, inspected gas piping and safeties, checked blower and inducer motor as well as cleaned and checked flame sensor and hot surface igniter. Burner and heat exchanger was inspected. No issues with unit at this time.

Completed plan member heat tune up for 80,000 BTU natural gas furnace. Aprilaire 501 filter ok Inspected runners, heat exchanger, inducer assembly, pressure switches Verified inducer draft Cleaned flame sensor and verified flame rectification circuit Ignitor in good condition, verified ohm reading Made adjustment to gas pressure to be manufacturers target 3.5” Inspected wiring and controls; left estimate for X13 blower motor surge protector; verified that heat fan speed is correct using airflow performance chart Inspect drains; there are no water safeties; I discussed nd left estimates for EZ trap and wet switch Measured temperature rise and static pressure (79-121° Good) Combustion and draft tests: Pass System operating well at this time. Homeowner renewed and paid for plan today.

Gas furnace tuneup on a 90% furnace . Checked the air filter and replaced . Checked the wiring connections and the voltages . Flushed the drain lines and furnace traps and inspected the condensate pump. Inspected the burners and flame sensors and cleaned . Inspected the flue pipes for leaks and bellies. checked the thermostat in heating mode and checked the gas pressures and the furnace safeties. checked the motor amps on the inducer operation and blower motors. Took indoor heat temp rise and tested for combustion on the system. The furnace is in good working order at this time of service.

Replacement of the OEM X13 Blower Motor for the Carrier system covered under Manufacturers Parts Warranty. Turn Power Supply off to the system. Disconnect and remove the existing Blower Motor and Housing. Install the new Blower Wheel and reassemble the Blower Housing. Complete all electrical connections and program motor as needed. Restore power supply and put into operation to test. Complete all warranty paperwork and return part to manufacturer for processing. *Part is 1-2 Business Days from the Manufacturer* 12/3/24- came to replace blower motor. When I pulled the motor out the blower wheel is destroyed. Will need blower wheel as well.

Completed heat tune up for 100,000 BTU natural gas furnace. Replaced Aprilaire 501 filter provided by homeowner. This is the last of these filters he has on hand. I let him know. Replaced Aprilaire 35 water panel provided by homeowner. Set humidistat to 35% Checked operations. Inspected burners, heat exchanger, inducer assembly Inspected wiring, controls, electric motors and components; discussed installing blower motor surge protector. Homeowner agreed, I installed blower motor surge protector today. Cleaned flame sensor and verified flame rectification circuit Ignitor in good condition, checked ohm reading Confirmed manifold gas pressure Measured temperature rise and static pressure Combustion and draft test: Pass Left estimate for tankless water heater service for next spring. Homeowners renewed plan membership. Paid for invoice today (plan and surge protector) System operating well at this time.

Found failed 3/4 HP X13 blower motor for Carrier gas furnace. Proved that the control board is providing 24V to the motor when there is a call for blower and that blower has 120V Equipment is 3 years old. Attempted to source motor today. Not available. We will verify warranty status and take into consideration. We will contact homeowners Monday as soon as we determine availability. ASAP System is down for now. Homeowner paid diagnostic today.

Unit was working fine in heating. I walked through remote operation with homeowner, Mode symbols, fan speed options. The indoor fan may not instant.y respond to a demand for heating based on the fact that he indoor coil needs to get to a designed temperature before the fan will energize Temperature rise 30° She mentioned that she would prefer a wall mounted thermostat if that option is available. I only know of wired options. We will research options. I left estimate for plan membership for this system (Minisplot with 1 indoor head). System was installed NOV 2023