Media, PA

Installed new Bosch gas furnace. Installed Aprilaire 2410 filter box. New 14x25 return drop and new supply plenum. New 30x30 drain pan, wet switch, condensate pump, EZ Trap and vinyl. Adapted to existing 3” PVC. Added intake drain. Adapted to existing fuel line. New blower surge protector. Installed new Bosch heat pump. New 30x30 pad with snow legs. New disconnect with surge protector. Flushed line set. Reinstalled REME halo and steam humidifier. Cleaned and tested out operations. Check pressures in spring time. Customer says they already paid $8,001.00 to dillan

Estimate

Fully assessed 2013 Amana hybrid system with heat pump and back up gas furnace. Other company mentioned that the blower wheel had some wobble to it. Examined blower motor as it was running and found that the blower wheel did have some wobble to it and this repair would require replacement of variable speed blower motor And blower wheel. This repair and itself would be almost $2000. Looked over heat exchanger and found a decent amount of rusting corrosion inside the heat exchanger did not see any holes but definitely a lot of corrosion. Went outside to outdoor heat pump to check operation of heat pump system. Found compressor did start a little rough one time when I cycled system. After fully assessing system would recommend replacement. Set up appointment to give a replacement quote.

estimate

Return visit to replace hydronic parts. Thermal expansion valve spiral vent repair kit new pressure relief valve new boiler drain. and add purger on the return side of boiler. Also during same visit replace water heater expansion tank. Add pressure 65 psi in common water pressure 65 psi. Cycle boiler test operation ok pressure and temp ok. Both zones are heating.

No heat from carrier geothermal unit found blank thermostat upon arrival. Check operation of unit found 30 amp double pole breaker in the off position at the electrical panel. Was not tripped. Reset breaker and went to thermostat set thermostat to heat 5° higher the room temperature no operation from thermostat. Remove thermostat from base and reinstalled it unit came on, test operation check supply and return our temperature 19° split 85° out 65° in check water temperature in and out 56° coming in 32° water going out. Cut j3 jumper at board to match system style 10 degrees coil. System uses antifreeze. System stay running the whole time during a troubleshooting. Not sure why the breaker trip at this time potentially compressor starting to go bad. Perform mega test reading on compressor check capacitor OK.

Perform tuneup on Goodman heat pump, ran system and emergency heat and tested heat strips and indoor unit, including indoor coil and blower motor. Went to outdoor unit and checked unit and heat pump mode and observed all electrical and mechanical components in the outdoor unit, including the compressor and outdoor fan motor, Capacitors and contactor were also checked , no issues with the unit at this time. Job is labeled as a gas furnace. It is a heat pump pump with an air handler in the attic.

Talk to Mike upon arrival he replaced the fuse soon as he replaces a fuse trips direct operation troubleshoot system check every low-voltage wire and component load. Found fusible link limit switch barely touching one of the burners. Corrected position of link and installed new 3 amp fuse. Test operation of boiler ok recycle boiler couple times ok. No charge warranty from last Visit.

Arrived to perform gas boiler tuneup. Upon arrival customer describe a problem he’s been having with relief leaking. Check operation of boiler check all safeties aquastat noticed there are using another aquastat on supply temperature pipe. Both Aqua stats were set to 200 Fahrenheit. Use my thermometer to check supply and return temperature as close as possible to the boiler and adjust temperature line aquastat to 180 Fahrenheit. With differential 165 F. During the tuneup, monitor water, pressure and temperature inspect expansion tank expansion tank has no air, but no water either. Relief pressure from the boiler to inspect expansion tank pressure added air to tank 15 psi. Test water feeder water feeder was not working. Had to add water manually in the same time. Inspect spiral vent spiral vent was not releasing any air. Recycle boiler couple times Boiler maintain pressure and temperature talk to customer about today and provide some recommendations replacement of expansion tank relief

Rafter vents, attic air seal, duct sealing in attic/basement, and ventilation of both upstairs bathroom exhaust fans