Cochranville, PA

Diagnostic tool read no ignition. Bled pump. Lots of water and sludge for a while but eventually got to oil. Tested system afterwards. Also replaced the old purge tee caps with brass ones. I had broken one of the old plastic ones during tune up. This where water was trickling. Educated Carl about keeping tank full and how to bleed pump. And that he will need to bleed when the tank is filled with oil soon. Carl has oil ordered. No charge because I did not replace the one cap.

Completed oil boiler tune up. One thermostat. No zoning. There are (2) purge tees on return and (2)on supply. See photos. One of the caps of the purge tee crumbled off. Cleaned heat exchanger and flues. Chimney is clear Replaced RF1 oil filter, replaced strainer, replaced nozzle .85 60B Verified pump pressure is target 140 psi Bled oil lines and tested operations. Monitored boiler temperature and pressure. Measured piping delta. I noticed the 1 return was not getting as hot and may be air bound. Recommend replacing the purge tee there which includes bleeding air out that particular side of the baseboard. Smoke, draft and combustion tests: Pass The auto air vent on top of air scoop is failed. Left estimate for this. Left estimate to add female adapter and proper length of copper for relief valve. Boiler operating ok at this time. During al conversation with homeowner he said he has had to close the supply valve for the second floor because it will get to 70° degrees there. Curr

Customer called in for a water leak found heater running upon arrival. Inspect condensate and drain system noticed broken check valve on pump informed customer that new pump it’s needed provided estimate for replacement, customer approved repairs after the repairs test condensate pump couple times no leaks present. Move wet switch away from pump until area is dry. Customer to put water sensors back in place.

Found oil boiler not running when I arrived. Slipped on emergency switch and burner tried to run but didn’t fire. Found clogged up .85 x 60‘b oil nozzle. Replace nozzle and oil boiler did fire. Oil boiler needs a very good cleaning. Recommended getting the maintenance plan. Decided to sign up for maintenance plan will need to schedule return visit to complete oil maintenance. Boiler is working at time of service.

11/1/24. Removed existing inducer motor assembly and collector box. Found bolts rusted and corroded had to break old collector box to remove. Installed new collector box with high temperature silicone sealed up installed new inducer motor assembly. Tested operation. No water leaks found perform combustion test. Gas furnace is working fine at time of service.

Went into the attic and took photos of roof to get a placement for attic van. Found the attic light is a pull down chain and only thing on that line. can put a junction box in and pull electrical from that to supply attic fan. Anthony said that he has been having problems with gnats so he would like a constant flow of air to help with gnats.

Performed tuneup on five year-old Goodman furnace, performed combustion analysis and checked all related ignition components including hot surf igniter cleaned flame censor and tested inducer motor. Checked blower capacitor, and blower amperage as well as changed filter and checked the temperature split of the unit. An issue was noticed that was related to the condensation produced by the gas furnace and through further inspection. It was noted that the collector box where the inducer motor mounts was leaking at the bottom, the bolts for the inducer motor rusted out and the inducer motor is amp higher than normal, customer customer was given an estimate to replace the parts related to the issue and they accepted. Parts need to be ordered and a return visit is required to install them. Mn-gmss920803bnaa Sn-1904030981

Perform tuneup on 8 year old luxaire gas furnace, Checked combustion and all associated ignition components, including flame sensor cleaned flame center, checked burners and gas pressures. Checked blower, motor capacitor, and inducer motor, Filter was changed. Delta t Was taken as well as combustion analysis. Unit is running good at this time. Customer was recommended a surge protector.

Installed overflow safety switch in secondary port of drain pan; wired to shut equipment down when overflow occurs. Installed AG3000 surge protector at air handler. Installed AG3000 surge protector at outdoor equipment disconnect. Afterwards cleaned area under attic access and tested system operations. Set thermostat back to “Cool 82°” System operating well at this time.

Completed AC tune up for 2 ton Rheem heat pump system. Inspected condition of both the indoor and the outdoor coil. Some rust/corrosion on indoor coil Filters should be replaced ASAP. Talked to Emily who said she will do it. 2 custom sized filters. Measured temperature split (67-47=20°) Good Inspected drain and pump, tested pump. Left estimate for overflow safety switch. Checked wiring, controls, electric motors and components. Monitored R10A refrigerant pressures. Suction pressure a little low but there was no load (return temp 67 and filters dirty.) System operating well at this time. System is at the age where major component failure can occur and is considered average system age for a heat pump system.